• Out-of-Stock

 Wax Necessities WX-1C Wax Cartridge Heater:

Technical specifications:
Voltage: 110V
Frequency : 50Hz/60Hz
Power: 40W
Volume: 1pcs*100G
Max Temperature:100 degrees C
Fits standard cartridges with the following measurements:
Height: 13.5 cm / 5.31 inch
Length: 5.5 cm /2.16 inch
Width: 2.25 cm / 0.88 inch
Warranty 1 year
Ideal for use with all Wax Necessities soft wax cartridges, the WX-1C heater offers a simple and reliable service. On the exterior, the heater is molded in a highly resistant APS thermoplastic plastic resin. and aluminium is used for the quality of inner construction.
To prolong the life and efficiency of the warmer, it is recommended a Wax Necessities soft wax cartridge always be inserted into the heating chamber. Never pour wax directly into the heating well.
To maintain the optimum condition of the heater, clean it regularly. Use Wax Necessities Citrus Cleaner for heavy wax residues. Do not use Citrus Cleaner directly on the `Wax Necessities`LOGO printed on the heater.
Your warmer has been tested before leaving the factory and is guaranteed against all manufacturing defects, under normal use, for 12 months from the date of purchase. If the heater will fail to operate due to a defect in material or workmanship, we will repair or replace it with date proof of purchase. The guarantee does not apply to damaged lids or heater resulting from misuse or accident.
Remove the heater lid and place the wax cartridge directly into the heating chamber (We recommend WaxNecessities cartridges).
Plug in the appliance. Redlight indicates power is on.
The indicator light will remain illuminated during operation time. Please allow 10-30 min, depending on the ambient temperature until the wax is ready to use.
To ensure the wax has reached a suitable temperature and to avoid loss of working time, it is recommended to plug in the heater approximately one half hour before services begin.
Unplug and cover the unit loosely with the lid when not in use.
CAUTION: Locking the lid tightly may cause the lid to break. If the lid adheres to the melting pot,pre-heat the warmer prior to lid removal to prevent it from cracking.
Recommended Wax Necessities cartridges.
Ideal for all Wax Necessities Cartridges 3.4 oz.
Read all instructions before using the heater!
When using electrical appliances, basic safety precautions should be followed.
To reduce the risk of burns or Injury:
Always test the wax on a small area of the skin before application.
Do not touch the metallic surfaces of the warmer. The unit is hot when in use.
Use only on a solid, surface.
Do not plug in the unit where the power cord can be tripped on or where the cord hangs over the edge of the working table and can be pulled off.
Do not leave the unit ON, unattended.
If the wax begins to smoke, unplug the unit immediately and have checked by an electrician.
Allow the unit to cool before, cleaning or storing.
Do not leave children unattended around the working heater. Use the unit only for the intended use as described in this booklet.
For best results, also refer to Wax Necessities waxing instructions on the product package.
Do not use it in bathrooms or on wet floors and surfaces.
lf unit falls into the water, unplug it immediately. Do NOT reach into the water.
Never operate the heater if it has a damaged power cord or plug, if it is not working properly. or has been dropped or damaged.
Do not connect more than 3 heaters on an extension cord.
For professional use only!

Natural Premium Soft Wax Cartridge 3.38 oz /100 g:

Transparent wax with a special delicate formula for sensitive zones. The wax follows the body curves and easily captures the short and coarse hair on uneven surfaces.
While applying, the wax temperature is very low, which makes it ideal for sensitive skin in delicate areas.
Temperature: max 42 degrees C (107.6 degrees F)
- Use applicator

- Use with strips
- Dye-free
- No artificial scent
- Transparent
1. Insert the cartridge into the heater and warm up (118F).
2. Apply the wax to the skin in the direction of hair growth.
3. Press the depilation strip on the treated area wax.
4. Remove the strip with a sharp pull against the direction of the hair growth.
5. Use after wax lotion.
Ingredients: Triethylene Glycol Rosinate, Glyceryl Rosinate.

- Please read the instructions in full before proceeding with the treatment. Failure to follow instructions and warnings may result in severe skin irritation and other injuries.
- Before using, test a small area to be waxed and wait 24 hours. If no irritation occurs, you may proceed to use it.
- Do not apply wax on mucous tissues, blemishes, moles, warts, varicose veins, sunburns, or any inflamed areas.
- Do not wax if you use creams with tretinoin, chemical peels, or have had plastic surgery, without a doctor's release.
- Do not use it if you suffer from any medical condition that may affect or compromise the skin.

- Consult a doctor before using if you suffer from any skin-related disorders, circulatory problems, or diabetes.
- Do not use on nipples, perianal, vaginal, or genital areas. Do not use it to remove hair inside the nostrils, ears, eyelids, or eyelashes.

- Do not use on areas that have been shaved, waxed, tweezed, or treated with hair removal creams within 24 hours.
- Avoid HOT baths, tanning beds, direct sun exposure, swimming, saunas, or other activities that may cause skin irritation.

Non-Woven Epilating strips:


These strips will help to achieve flawless removal of wax on large body areas.
Package of high-quality 100 epilating strips.

3 inch x 8.75 inch
Perfect for the body and legs.

IMPORTANT NOTE: Professional Use Only! Please read carefully all the instructions on the product label before use.


Download MSDS data sheets



Data sheet

Application direction
Hair growth direction
Skin type
All Skin Types
Application area
Free of
Artificial Colors
Synthetic Fragrance

You might also like

In the same category