• Out-of-Stock

Ideal for use with all Wax Necessities soft wax cartridges, the WX-1C heater offers a simple and reliable service.

On the exterior, the heater is molded in a highly resistant APS thermoplastic plastic resin, and aluminum is used for the quality of the inner construction.

To prolong the life and efficiency of the warmer, it is recommended a Wax Necessities soft wax cartridge always be inserted into the heating chamber. Never pour wax directly into the heating well.

To maintain the optimum condition of the heater, clean it regularly. Use Wax Necessities Citrus Cleaner for heavy wax residues. Do not use Citrus Cleaner directly on the `Wax Necessities` LOGO printed on the heater.

Your warmer has been tested before leaving the factory and is guaranteed against all manufacturing defects, under normal use, for 12 months from the date of purchase. If the heater will fail to operate due to a defect in material or workmanship, we will repair or replace it with date proof of purchase.

The guarantee does not apply to damaged lids or heaters resulting from misuse or accident.

Wax Cartridge not included!

   

INSTRUCTIONS FOR USE

- Remove the heater lid and place the wax cartridge directly into the heating chamber (We recommend Wax Necessities cartridges).

- Plug in the appliance. The red light indicates power is on.

- The indicator light will remain illuminated during operation time. Please allow 10-30 min, depending on the ambient temperature until the wax is ready to use.

- To ensure the wax has reached a suitable temperature and to avoid loss of profitable working time, it is recommended to plug in the heater approximately one half hour before services begin.

- Unplug and cover the unit loosely with the lid when not in use.

- Caution: Locking the lid tightly may cause the lid to break. If the lid adheres to the melting pot, pre-heat the warmer prior to lid removal to prevent the lid from cracking. 

- WARNING: HEATER AND WAX ARE GETTING HOT. ALWAYS TEST WAX ON A SMALL AREA OF SKIN PRIOR TO APPLICATION.

- Ideal for all Wax Necessities Cartridges 3.4 oz

 

Fits standard cartridges with the following measurements:

- Height: 13.5 cm / 5.31 inch

- Length: 5.5 cm /2.16 inch

- Width: 2.25 cm / 0.88 inch 

    

IMPORTANT SAFETY INSTRUCTIONS:

- Read all instructions before using the heater! When using electrical appliances, basic safety precautions should be followed.

- WARNING To reduce risk of burns, fire, or Injury:

- Always test the wax on a small area of the skin before application.

- Do not touch the metallic surfaces of the warmer.

- Unit is hot when in use. Use only on a flat, solid, surface.

- Do not plug-in unit where the power cord can be tripped on or where the cord hangs over the edge of the working table and can be pulled off.

- Do not leave the unit ON unattended.

- If wax begins to smoke, unplug the unit immediately and have checked by an electrician.

- Allow the unit to cool before, cleaning or storing.

- Do not leave children unattended around the working heater.

- Use the unit only for the intended use as described in this booklet.

- For best results, also refer to Wax Necessities waxing instructions and instructions on the product package.

- DANGER To reduce the risk of electrocution: (which can result in injuries or death)

- Unplug the heater immediately after use.

- Do not use it in bathrooms or on wet floors and surfaces.

- If the unit falls into water, unplug it immediately. Do NOT reach into the water!

- Never operate the heater if it has a damaged power cord or plug if it is not working properly or has been dropped or damaged.

- Do NOT connect more than 3 heaters on an extension cord.

   

IMPORTANT NOTE: Licensed beautician use only! Please read carefully all the instructions on the product label before use.

SKU006535

Data sheet

Color
Pink
White
Country
China

You might also like

In the same category